This is an outdated version published on 2025-12-12. Read the most recent version.

OPTIMIZATION OF THE PARAMETERS OF THE ROTATION ROLLER USED FOR PROCESSING COTTON BROADS

Authors

Tolibayev Alpisbay Yerzhanbayevich doctor of technical sciences, senior researcher (SSISTT) Author
Ibragimov Kuanishbay Zhanabayevich basic doctoral student (NIIMSX) Author

Keywords:

cotton cultivator, rotary ripper, cross blades, vertical load force, loosening depth, unit speed, optimization.

Abstract

In this article, the issue of optimizing the parameters of the developed rotary cultivator for cotton cultivators is considered. In this case, such factors as the distance (height) of installation of transverse knives on the disk of the rotary ripper, the number and width of the knives, the force of vertical pressure on the rotary ripper, and the speed of the unit were taken into account. The results of the conducted research show that at the working speeds of the unit of 5.0-6.0 km/h and the number of cross-knives 14 pieces, the distance of installation of cross-knives on the disk of the rotary ripper should be within 2.0 cm, the width of the cross-knives of the rotary ripper 5.0 cm, the vertical load force applied to the rotary ripper should be within 366.0-428.0 N. As a result of the conducted research, it was established that the distance of installation of cross-knives on the disk of the rotary ripper should be within 2.0 cm, the width of the cross-knives of the rotary ripper 5.0 cm, the vertical load force applied to the rotary ripper should be within 366.0-428.0 N.

References

1. Пахтачилик маълумотномаси. – Тошкент: Fan va teхnologiya, 2016. – 540 б.

2. Хожиев А. Пахтачилик культиваторининг комбинациялашган иш органи / Монография. –Тошкент: Адабиёт учқунлари, 2014. – 72 б.

3. https://www.google.com/search

4. Отчет о научно-исследовательской работе по проекту КХА-3-024 за 2014 г. по теме: «Разработка энерго-ресурсо и влагосберегающей универсальной машины для обработки почвы в междурядьях и рядах садов» (заключительный) – Самарканд: СамСХИ, 2014. – 84 с.

5. Ўзбекистон Республикаси патенти FAP № 2696. Қишлоқ хўжалиги экинлари қатор ораларига ишлов берадиган осма култиватор // Ибрагимов А.А., Абдурахманов А.А., Ибрагимов Қ.Дж, Оринбаев П.Ф. // Расмий ахборотнома. – 2025. – № 5 (290).

6. Толибаев А.Е., Толибаев Р.Т., Шербаев Р.Т., Жумамуратова В. Results of experimental study on hill seeding of mung beans // Journal of advanced scientific research (ISSN: 0976-9595) Vol.6. Issue 8 page 41. Impact factor 9.

7. Tolibaev A.E., Mirjalilov M.M. Results of studies to substantiate the parameters of the working parts of the combined unit // Journal of Engineering Mechanics and Modern Architecture. – Vol.3., No 10, 2024. – Pp.89-93.

8. Толибаев А.Е. Пушта тепасига минимал ишлов берадиган иш органларнинг параметрларини асослаш //Ўзбекистон қишлоқ ва сув хўжалиги. – Тошкент, 2023. – №2. – Б.55-57.

9. Аугамбаев М, Иванов А.З., Терехов Ю.И. Основы планирования научно – исследователского экспреримента. – Ташкент: Ўқитувчи, 1993. – 336 с.

10. Доспехов Б.А. Методика полевого опыта. – Москва: Колос, 1978. – 335 с.

11. Толибаев А.Е., Ибрагимов Қ.Ж. Ғўза қатор ораларига ишлов беришда қўлланиладиган иш органларнинг турини танлаш бўйича ўтказилган таққослов синов натижалари//Agro ilm. – Тошкент, 2025. – №7 (116). – Б.136-137.

12. Электрон ҳисоблаш машиналари учун яратилган дастурининг расмий рўйхатдан ўтказилганлиги тўғрисидаги Гувоҳнома. Ўзбекистон Республикаси адлия вазирлиги. № DGU 27277. Рўйхатдан ўтказилган сана 07.09.2023 й.